Q acoustics 2010i manual

This makes it possible to create a 5. What is bluetooth? Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

Is the manual of the Q Acoustics i available in English? Yes, the manual of the Q Acoustics i is available in English. Q Acoustics. Room positioning has a dramatic effect on low frequency reproduction of both the sub-woofer and your main speakers so don't be worried if you find you require a setting which does not correlate with the specified low frequency point of your main speakers. Setting up can take many hours of listening because all of the controls on your subwoofer will interact; there is no easy route to success.

The best phase invert switch position is strongly affected by the chosen crossover frequency so as you fine tune the controls you may wish to keep trying the alternative setting to see which you prefer.

Once you feel you are close with the settings you can now perfect the integration between sub-woofer and main speakers by adjusting the phase control. This control affects the level of bass produced at the crossover frequency and also how smoothly the transition occurs. Again this will interact with the crossover control so fine adjustments of the crossover frequency may be necessary to produce the best results.

Also you may find you can get to a better end result by flipping the phase invert switch and trying to optimise the crossover and phase controls again. Experimentation is the key to getting perfect integration; once this is achieved you should never be aware of any sound coming from the direction of the sub-woofer itself.

The end result will be a system with powerful, extended bass response which appears to be coming from the soundstage between the main speakers. The Front Speakers are bi-wired. This is the preferred mode of connection provided the crossover network supports biwiring. When running loudspeaker cables be especially careful not to run them across open floor areas where they could be a source of danger.

Run loudspeaker cables around room boundaries whenever possible. Line level signal cables should be run away from mains cables. Never run line level signal cables parallel to power cables especially on long runs. If the subwoofer is triggered on by appliances switching on and off, re-route the input signal cable before taking further measures. The 6. The 5. Placement: The Front and Centre speakers should be in line. If you have a 5. As always, be prepared to experiment.

Set up each individual speaker so that the level is the same at the listening position as all the others. If your processor enables you to adjust the delay times, follow the instructions closely as this will profoundly affect the final result. You may however have to adjust the subwoofer level both at the processor and at the subwoofer. Once set, do not re-adjust these levels. If this occurs, reduce the level immediately.

Phase: If your speakers are incorrectly wired the bass will be blurred and thin. In this case, check the wiring carefully. If your speaker wire has a tracer along one core, consistently use the striped core to connect all the positive RED terminals. In this way the system will always be in phase. Clean cabinets with a barely damp cloth. Do not use solvent based cleaning materials. If the cabinets become stained, remove the stain with a cloth lightly moistened with water, white spirit or isopropyl alcohol depending on the stain.

Then lightly buff with a cloth to remove any residue of the cleaning agent. Never use abrasives of any kind. Lightly brush out grilles with a soft brush. Do not remove the speaker grilles unless absolutely necessary.

Q Acoustics loudspeakers are warranted free of defects in materials and workmanship as follows:. Goods for repair should in the first instance be returned to the supplying dealer.

Damage sustained by goods in transit to the repair centre is not covered by warranty. Return carriage will be paid by Q Acoustics or their distributor as appropriate. Remarque importante pour les utilisateurs au RoyaumeUni. Notre gamme comprend :. Montez graduellement le son. Ne laissez PAS vos enceintes dans des endroits trop froids, trop chauds, trop humides ou au soleil. Votre revendeur pourra vous conseiller.

Ne vous servez pas de sacs en pour les soulever. Ne placez pas d'objets sur le haut-parleur, quels qu'ils soient. Enfichez le cordon d'alimentation fourni dans le haut-parleur des graves, puis dans la prise femelle d'alimentation AC. Choisissez le haut-parleur avant le plus proche du haut-parleur des graves et lisez la piste correspondante.

Par exemple, s'il s'agit du haut-parleur droit avant, lisez la piste trois. Le haut-parleur des graves ajoutera automatiquement les signaux L gauche et R droit ensemble pour qu'aucune information ne soit perdue. Branchez le cordon d'alimentation fourni dans le haut-parleur des graves, puis dans la prise femelle d'alimentation AC. Les raccordements pour un 6. La disposition du 6. Le positionnement du 5. N'utilisez jamais de produits abrasifs. Epoussetez les grilles avec une brosse douce.

Les frais de renvois seront pris en charge par Q Acoustics ou par leur distributeur. Conservare le istruzioni per un uso futuro. Rispettare tutte le avvertenze inerenti ai rischi. Seguire tutte le istruzioni. Pulire esclusivamente con un panno asciutto. Non ostruire nessuna apertura per la ventilazione.

Installare conformemente alle istruzioni del fabbricante. Una spina con presa di terra dispone di una coppia di lame e di un terzo polo di messa a terra.

Qualora la spina in dotazione non si adatti alla propria presa di corrente, consultare un elettricista che provveda alla sostituzione della presa obsoleta. Per qualunque operazione di manutenzione rivolgersi a personale specializzato.

Il prodotto non deve essere esposto a gocce e spruzzi e sopra il prodotto non deve essere collocato nessun oggetto contenente liquidi, come vasi di fiori. Non collocare sopra il prodotto nessuna fonte di fiamma non protetta, come candele. Questo interruttore si trova nel pannello posteriore. Qualora fosse necessario sostituire la spina, rimuovere il fusibile e smaltire la stessa, in modo sicuro, subito dopo averla recisa dal filo.

La gamma include:. Tutti gli altoparlanti si possono mettere in funzione vicino ai monitor televisivi senza effetti indesiderati tranne nel caso del Si, che non deve essere azionato entro il raggio di mm da schermi televisivi, monitor o altre attrezzature magnetosensibili. Nessun effetto sugli schermi al plasma e a cristalli liquidi.

Prima di procedere con qualunque collegamento agli altoparlanti assicurasi che tutti gli apparecchi sotto tensione del sistema siano spenti alla rete. In fase di accensione del sistema acustico o di modifica delle fonti di ingresso, impostare il regolatore di volume principale su un livello basso.

Alzare poi il livello gradualmente. La posizione del regolatore di volume inganna e non segnala il livello effettivo di potenza del sistema.

Sistemare lo scaffale approvato dalla Q- Acoustics seguendo le istruzioni e utilizzando qualunque fissaggio in dotazione. Disimballare tutte le componenti degli altoparlanti. Sollevare gli altoparlanti dalle scatole reggendo gli armadietti. Non utilizzare i sacchi di politene per sollevarli. Il i, e Si sono pesanti, se necessario, chiedere aiuto per sollevarli.

Nel maneggiare gli altoparlanti non trascinarli sul pavimento per non procurare danni — sollevarli prima di spostarli. Controllare attentamente il prodotto. In caso di parti danneggiate o mancanti, rivolgersi il prima possibile al proprio rivenditore. Conservare la confezione per il trasporto del prodotto in futuro. Non collocare mai un altoparlante con i chiodi laddove questo possa arrecare danni! I diffusori della serie i sono retroventilati e progettati per funzionare in modo ottimale lasciando circa mm di spazio libero rispetto alla parete.

I tamponi devono essere inseriti nella porta senza forzare. Provare a modificare la posizione del diffusore poco per volta, fino ad individuare la soluzione ideale. Gli altoparlanti i vanno collocati almeno a mm di distanza dalla parete posteriore e a mm di distanza dalle pareti laterali. Sono inoltre disponibili i supporti da pavimento per i modelli i e i. Si deve collocare subito sopra o sotto lo schermo. In caso contrario, si consideri. Thin cables reduce the bass and restrict the dynamic range.

Surround rear channels are less critical. Speaker cable has a stripe or tracer along one core. By convention this is connected to the positive terminals. The cables connecting the amplifier. Bare the wire to a depth of 10mm and twist 30mm the ends to gather any stray wires.

Crop the. Unscrew the terminal anticlockwise to expose the mounting hole in the base of the. Insert the bare end of the cable into the hole. Re-tighten the terminal fully hand tight. Make sure there are no stray wires which could touch adjacent terminals. When your speakers are connected: Switch on the system and play some music at moderate level. Fine tune the speaker placement to suit. The subwoofer is set to the voltage in your area.

If you move to an area with a different voltage, take the unit to a qualified technician to have the voltage changed. This is something that you should not do yourself.

Before connecting the subwoofer please make sure that all the active units in your system are switched off at the mains. Bass frequencies are substantially omnidirectional. Although this means that you can position the subwoofer almost anywhere, the stereo image will still benefit by siting the subwoofer level with the front loudspeakers and as central to the listening position as possible.

This may not be feasible in a multichannel system. If you place the subwoofer close to a wall the bass will be re-inforced though in some locations the bass may be boomy and indistinct. Do not place the subwoofer across a corner. The subwoofer should be positioned close to a mains power source. Do not use extension cables. Purchase a longer power cord if necessary. There should be ample free space between the rear of the cabinet and any wall or other object to allow free unrestricted access to this switch.

When siting the subwoofer ensure the floor is sound with no loose floorboards etc. The air movement from the subwoofer at high volumes is substantial - do not place it close to soft furnishings or objects that may rattle. Do not place objects of any kind on the unit. You will need a single RCA phono interconnect. As this cable is likely to be quite long, make sure you get a good quality fully screened cable.

Your Q Acoustics dealer will be happy to supply you with a suitable interconnect. Push the plugs firmly home to ensure a good contact. Your dealer will advise you about a suitable adaptor. Alternatively, use the High Level connection. In this mode the subwoofer is connected to the amplifier together with the Front loudspeakers.

This connection should be used only if a dedicated subwoofer line output is unavailable. Prepare two lengths of twin core loudspeaker cable. Unscrew the high level terminals on the rear of the subwoofer. Repeat this procedure for the LEFT channel. Leave the front loudspeakers connected. The internal circuitry of the subwoofer will combine the front channels to produce a single common bass channel.

Check that all system connections are properly and securely made. Ensure that the subwoofer is switched off. Set the subwoofer level control roughly halfway. Set the crossover control to 70Hz. Plug the supplied power cord into the subwoofer and then into the mains point. As there is a close relationship between the subwoofer volume, its physical position and the crossover frequency, mutual adjustments to all three may be necessary before the system is fully set up.

Level: The Level Control sets the volume of the subwoofer relative to the other speakers in the system. Set a level that enhances the bass of the system. There should be a seamless blend between the front speakers and the subwoofer. Crossover frequency: Set the crossover control according to the size and low frequency extension of the front speakers.

The role of the subwoofer is to extend the bass response of the system and not to increase the overall bass level. If the loudspeakers are large, a value between 50 and 60 Hz is probably about right. With smaller speakers such as the i, this can be increased as far as 90Hz.

At higher settings the subwoofer may become intrusive and low level detail and definition may suffer. As always the final settings should be determined by listening. You should listen to a wide range of music at different volume settings while doing the setup. One setting will offer fuller and more extended bass than the other. As the effect can be quite subtle, especially with small loudspeakers where relatively more bass is coming from the subwoofer, extended listening and experimentation may be necessary before the final decision is made.

Auto Power On: This feature enables you to switch the main system on and off without having to remember to switch the subwoofer on and off as well.

The Si has a built in level sensor. If there is no input, after a short time the subwoofer will automatically power down into Standby mode. As soon as the subwoofer senses an input it will automatically switch into operational mode and the power light will again glow green.

The Front Speakers are bi-wired. This is the preferred mode of connection provided the crossover network supports bi-wiring. When running loudspeaker cables be especially careful not to run them across open floor areas where they could be a source of danger.

Run loudspeaker cables around room boundaries whenever possible. Line level signal cables should be run apart from mains cables. Never run line level signal cables parallel to power cables especially on long runs.

If the subwoofer is triggered on by appliances switching on and off, re-route the input signal cable before taking further measures. The 6. You really can place these speakers anywhere. Multi award winning bookshelf speakers. They can be stand or wall mounted, using the dedicated ST stand or WB wall bracket, for ultimate flexibility.

Skip to the end of the images gallery. Images 3D View. Skip to the beginning of the images gallery.